NOMAD

NOMAD / EN

Cold tub chiller / EN

Documented configuration: 780 W / 2720 W, 470 × 500 × 600 mm. Verify the unit nameplate.

NOMAD 1.0 / 2026-10-31

Cold tub chiller

NOMAD adapted and translated user edition. This is not a manufacturer-authorised translation. Installation also requires the original documents for the actual model.

01 / Technical data

IdentificationConfiguration in NOMAD Chiller Operating manual; source does not state a unique model code
Dimensions470 × 500 × 600 mm
Input / cooling capacity780 W / 2720 W, declared sheet values
Pump60 W / 2000 l/h
UV / ozone18 W / 5 W, if fitted to the actual unit
Setting range in NOMAD source3–40°C; does not establish a heating function on every variant
Inlet / outlet filterStainless mesh / PP cartridge
Connections / hose¾″ / 19.05 mm; 2 m insulated hose
ConnectivityTuya Smart, if the Wi-Fi module is fitted
Packaging / gross weight63 × 51 × 68 cm / 45 kg
SupplyEuropean variant: 220–240 V, 50 Hz; verify nameplate
Frost protectionDo not use below 0°C ambient; drain water

02 / Identification and installation

Match the delivered unit

The source does not identify a unique model code. Compare the nameplate, dimensions, power and controls with the actual unit. If they differ, obtain the correct manual from NOMAD before starting. The photograph is a visual reference, not proof of compatibility.

After transport

After horizontal transport, keep upright for 12–24 hours before starting. After upright transport, the source recommends 2–4 hours. Follow any stricter requirements for the actual unit.

Position and power

Choose a stable, ventilated location without explosion hazards, corrosive gas, conductive dust or strong vibration. Prevent condensate from pooling. An electrician must verify supply, earthing and residual-current protection from the nameplate. The source reference to 16 A does not by itself specify every required protection characteristic.

03 / Starting and use

Fill first

Connect correctly identified inlet and outlet hoses, fill the bath and check every joint. Never start empty, obstructed or leaking. Start the pump and confirm normal water circulation.

Starting delay

Start using the unit control. A flashing indicator may indicate the approximately 3-minute start delay. In cooling mode check circulation and warm exhaust air. Do not alter service settings or assume heating capability merely because the source uses shared text for several variants.

Before touching water

The source requires unplugging before touching the water. Follow this before bathing or intervention. Never handle electrical parts with wet hands. Stop for leaks, unusual noise or protection trips.

Indicative cooling figures

The sheet gives these examples for 300 l, 25°C ambient and water starting at 25°C: approximately 2 h to 12°C, 4 h to 5°C and 5 h to 3°C. They are supplier examples, not guaranteed times for every bath, insulation or outdoor temperature.

04 / Care and support

Routine checks

With the unit unplugged, visually inspect hoses, joints, inlet filter and outlet cartridge. Keep ventilation clear. Follow the identified equipment instructions for cartridge cleaning/replacement and UV / ozone service. Never operate opened modules or improvise ozone dosing.

Frost and storage

The source prohibits operation below 0°C ambient. Drain the unit and connections completely before frost or storage. A Wi-Fi app or timer is not sufficient frost protection.

Requesting help

Send the nameplate, serial number, control-panel photograph, exact error code and water/ambient temperatures. The available source has no complete error-code list: do not guess codes or repeatedly restart a faulty unit. Support: [email protected], +40 745 524 215.

Sources and edition

NOMAD Chiller Operating manual.pdf.pdf

Configurație documentată / documented configuration

Keep this manual with the installation documents. Verify specifications against the nameplate; equipment and revisions may vary.

NOMAD support

[email protected] / +40 745 524 215